QTH.COM Ham Radio Classified Ads: TOWER - Swap amateur radio HF VHF equipment buy sell trade on line

For sale: Rohn 55 tower sections for sal: Rohn 55 tower pieces for sale. 2-10 foot straight sections, 1 tapered top section and 1 top plate. $950 for all as package only. Pickup only in Cooperstown, New York.; Listing #1770090 - Submitted on 06/04/26 by Callsign N2NKX - IP: syn-076-180-186-127.res.spectrum.com; Click to Contact -- Click Here to View Picture -- Send this Ad to a Friend
US Tower TMM-541-SS with Motor Drive: US Tower TMM-541SS, extends to 41' and max height of 47' with mast. Most importantly, for those who are not so keen on climbing towers, this one lowers to 12' for easy servicing / repairs via a step ladder, or for lower visibility to neighbors. In the pics the tower is prohibited from lowering all the way to 12' due to my rotator plug extending beyond the outer boundaries of the top tower section. With a slimmer rotor, or 90-degree plug, the tower lowers all the way down to 12'. The tower is equipped with the US Tower motor drive (MD-75), hinged T-Base and rotor plate. New price is $6,999.95 for the tower, MD-75 motor drive: $6,019.95 and tower base $1749.95
Tower is in nice condition and will support 18 square feet of antenna at 50 mph winds. It was re-cabled shortly before I purchased it in 2018 from the original owner W7RAW. Includes Structural Analysis Report from US Tower specific to this tower. Transport weight is 430 lbs. '73. N7AM Dallas, OR; Listing #1769896 - Submitted on 06/02/26 by Callsign N7AM, Modified on 06/04/26 - IP: 97-115-81-64.ptld.qwest.net; Click to Contact -- Click Here to View Picture -- Send this Ad to a Friend
Looking for ( 1 ) 10 ft -piece Rohn 45G: Hello Ham's, I'm looking for (( 1 )) piece of RHON-45-G tower the big stuff I can pick it up if not to far away let me know.
Thanks W4POO; Listing #1769820 - Submitted on 06/02/26 by Callsign W4POO - IP: syn-074-139-138-220.res.spectrum.com; Click to Contact -- Send this Ad to a Friend
For Sale: ROHN GA65GD: Guy bracket assembly for Rohn 65G tower. $160; Listing #1769723 - Submitted on 05/31/26 by Callsign KK9A - IP: customer.atlagax1.isp.starlink.com; Click to Contact -- Click Here to View Picture -- Send this Ad to a Friend
W9IIX Gin Pole head and clamps (no pipe): Vintage W9IIX Heavy Duty Gin Pole Head and Clamps
Up for sale is a classic, heavy-duty W9IIX (IIX Equipment Ltd.) gin pole head and two tower clamps. If you know tower gear, you know these are legendary for being incredibly rugged, over-engineered all-steel units that are virtually indestructible compared to modern lightweight alternatives. Designed for rigging Rohn BX/HBX/HDBX lattice towers.
Included in the sale:
•Original heavy-duty W9IIX open-face steel tower clamping brackets (2).
•Heavy steel head assembly with an intact, smooth-rolling pulley.
Pole Not Included:
You will need to locally source a 10-12 ft section of 2"od x 1-1/2"id pipe for the pole. I used galvanized water pipe. T6-6061 aluminum also works.
Good, solid condition. Shows typical signs of use but is 100% structurally sound and ready to go back to work on a tower project.
Price:
$400
Shipping/Pickup:
$35 USPS Flat Rate shipping or Local Pickup near Woodbury, MN.; Listing #1769668 - Submitted on 05/31/26 by Callsign K0JDD - IP: c-76-156-60-124.hsd1.mn.comcast.net; Click to Contact -- Click Here to View Picture -- Send this Ad to a Friend
For Sale: LOTS of R25 tower sections: I haven't counted but many R25 sections available. I'd guess over 200'. A few sections have very light surface rust. Not needed so pricing at below typical price.
Asking $50 per straight section.
Also 100' of what I think is Tri Ex tower. 10 ft sections. Bolt on cross braces. Make an offer.

Located in Pittsboro NC. Easy access to load on your trailer or truck.
Thanks
Ron
N4XD; Listing #1765559 - Submitted on 04/20/26 by Callsign N4XD, Modified on 05/31/26 - IP: 172.58.255.93; Click to Contact -- Send this Ad to a Friend
Want to buy: Heights crank up tilt over tower.
Cannot use steel tower--too heavy.
Any age will work.
Picture for attention...; Listing #1768759 - Submitted on 05/21/26 by Callsign W5XB, Modified on 05/30/26 - IP: c-73-82-201-3.hsd1.ga.comcast.net; Click to Contact -- Click Here to View Picture -- Send this Ad to a Friend
Rohn 40ft DOWN !: 40ft Roan tower SALE/down
Hi ,this tower has the other (4) 10ft parts .5 parts in all .Bring a TRAILER to pick up.$300 CASH firm. Other pics on request .Gillett P.A. pick up ONLY .W2TWM; Listing #1769606 - Submitted on 05/30/26 by Callsign W2TWM - IP: customer.nwyynyx1.isp.starlink.com; Click to Contact -- Click Here to View Picture -- Send this Ad to a Friend
FOR SALE HG54 CRANKUP TOWER: Got this Hg54 self supporting crank up tower about 6 months ago but my health prevents me from installing it
It has no rust ,It’s on the ground.
It comes with a winch ( not yet tested) and will need a base
It nests at 22feet
Can be inspected in Fern Park in Central Florida
Price $1500.00 negotiable
Note
If there’s someone who can install it , I will do that instead of selling; Listing #1769531 - Submitted on 05/29/26 by Callsign KB2SG - IP: 172.56.75.165; Click to Contact -- Click Here to View Picture -- Send this Ad to a Friend
Tower Base Leg Bolt Mounts for Concrete: Factory made. Unused.
5 ft tall
1” día steel bar tower base concrete anchors
3x20x3/8 bolt flange
2-1/2” centers
1-1/4” center from edge of flange
13/16” bolt holes
3 of them
350 cash
Dallas. Come get em; Listing #1769525 - Submitted on 05/29/26 by Callsign W5RL - IP: 216.76.52.43; Click to Contact -- Click Here to View Picture -- Send this Ad to a Friend